Pressure washing prices in the South Bay depend mostly on square footage, the number of stories, the surface (stucco, concrete, tile roof or pavers), how heavy the staining is, and how hard the property is to access. Published 2026 averages put a house wash at $312 nationally (most pay $213 to $449), stucco at $0.30 to $0.50 per square foot and driveways at $0.20 to $0.40 per square foot. Bundling a house wash, driveway and gutters in one visit usually costs less than booking them separately because there's only one setup and trip.
Key takeaways
- Size and stories matter most: a two-story house takes more setup and time than a single-story house of the same footprint.
- Soft washing stucco and tile roofs uses different equipment and cleaners than pressure washing concrete, so each is priced on its own.
- Oil, rust and gum need pre-treatments that add time.
- Handling runoff the way LA County requires is part of a proper job, not an extra.
- In California, a job of $1,000 or more in total labor and materials requires a licensed contractor.
The five things that set the price
Square footage of each surface. Driveways and patios are measured by area. House washes are usually based on the size of the home and its height.
Height and access. Second and third stories, steep hillside lots, tight side yards and rooftop decks all add setup time and safety work.
The surface. Stucco and painted siding are soft washed; concrete is surface-cleaned at high pressure; tile roofs are soft washed slowly and carefully. Each takes different equipment.
How dirty it is. A home that's been washed every year cleans faster than one with years of mildew. Set-in oil, sprinkler rust and gum each need their own treatment.
Runoff. A proper job keeps wash water out of the street and storm drain. Steep driveways and commercial grease areas take more work to contain.
Published averages
Angi's 2026 data, from 51,092 reported projects nationwide, puts the average cost to pressure wash a house at $312, with most homeowners paying $213 to $449. Per square foot, stucco runs about $0.30 to $0.50, wood siding $0.30 to $0.55, vinyl $0.20 to $0.50, driveways $0.20 to $0.40 and roofs $0.50 to $1.00. A one-story house typically runs $150 to $750 and a two-story house $400 to $1,400.
These are national figures, not our prices, and South Bay jobs often land at the higher end. Use the pressure washing cost calculator on this site to add up your surfaces, then get a written estimate for the real number.
Why online prices vary so much
National averages mix small single-story homes in dry climates with large coastal homes that need soft washing. South Bay homes near the water usually have more mildew and salt film, more stucco and more tile roofs than the national mix, so an accurate price depends on the actual property.
How to get an accurate written estimate
Send the address, the surfaces you want cleaned and the number of stories. A good company looks at the property, from street view or in person, and gives you a written estimate before any work starts. Be cautious of a price given without any look at the property, and of any price that seems too low to include runoff control.
The California license rule
Under California law, any home improvement or contracting job totaling $1,000 or more in labor and materials must be done by a contractor licensed by the Contractors State License Board. You can check a license number on the CSLB website.
Related questions
Is it cheaper to bundle house washing and driveway cleaning?
Usually, yes. One visit means one setup and one trip, so bundling a house wash with the driveway, patio or gutters typically costs less than booking each one separately.
Why does a two-story house cost more to wash?
Upper stories need more setup, longer reach and more safety precautions, and the crew covers more wall area. That adds time compared to a single-story home of the same footprint.
Does a pressure washing company need a license in California?
For any job of $1,000 or more in total labor and materials, California requires a contractor licensed by the Contractors State License Board. You can look up a license number on the CSLB website.